Re: About to call and break my new Home Alarm Agreement....
I agree fully with you! Please keep this forum updated!
View ArticleRe: About to call and break my new Home Alarm Agreement....
Couldn't agree more, very lame, my touch panel and mobile software is not in sync, door contact is shown as an open door and I can see on the camera it is NOT open. I bypassed the door zone with my...
View ArticleRe: About to call and break my new Home Alarm Agreement....
Tech came out, took a look at everything. Router "looks fine" but no way to really troubleshoot it. 1 camera wouldn't connect at all in the location it was originally installed in, so we had to move...
View ArticleMotion Sensor set to Interior Follower Arm Night? Then Armed Away motion...
So my tech came out today and I told him about how I really wanted to setup Night mode to have motion detection, and how I was able to set that with the technician code. He said the reason you don't...
View ArticleDisable motion sensor for all armed modes
Despite the pet immunity, my motion senson is constantly triggered by a 10lb cat. I highly doubt relocation is a possible solution. The sensor is mounted 9 feet up on a wall facing a large open area....
View ArticleRe: Disable motion sensor for all armed modes
I believe there is a setting called "24 hour follower" that is just basically leaving it on all the time, but not arming it. Try it out.
View ArticleRe: Disable motion sensor for all armed modes
Thanks, do you how to access that setting? I feel like I'm missing some things I had access to right after the install. I know I was in a place where I was able to see temperatures being reported by...
View ArticleRe: Disable motion sensor for all armed modes
That was the answer, thanks! The zone function setting is "24-hour Inform".
View ArticleRe: Xfinity Home Security and routing questions
My new router arrived from Amazon today. I replaced my old linksys (which wasn't that old really) with this one, got the firmware downloaded, network set up, etc, and went upstairs to reset my panel,...
View ArticleRe: Xfinity Home Security and routing questions
bbarley1 wrote:My new router arrived from Amazon today. I replaced my old linksys (which wasn't that old really) with this one, got the firmware downloaded, network set up, etc, and went upstairs to...
View ArticleRe: Xfinity Home Security and routing questions
Well, I read an earlier post from jeffnielson that the netgear XHS router needed a specific address starting with 76. I tried to set that up from the linksys, but it was a no-go since my Linksys was...
View ArticleAnyone get a WIFI extender to work?
So after meeting with our tech today, we found a few cameras were low on the signal level, not low enough to not work, but on the edge. So he said I could go get a signal repeater from Netgear. Well I...
View ArticleConnecting iCamera 1000 via POE
I have six ICamera 1000s on my Xfinity Home system and would like to switch from wireless to wired mode to increase throughput and improve video speeds. Knowing that the iCamera 1000 receives power...
View ArticleRe: Connecting iCamera 1000 via POE
The camera cannot be powered by a PoE switch only. You can use a standard switch and will always need to use the "y-cable" to put into wired mode. Thanks,Chris
View ArticleRe: How do I reset the low battery alert after changing batteries.
I tried everything in this forum and nothing worked to get rid of low battery alets on my touchscreen until i tried the following.Make sure your Thermostat is turned off and then push the reset button...
View ArticleRe: Xfinity Home Security and routing questions
Same frustration, Comcast router impacting my network, Airport Extreme complaining of dual NAT, port forwarding not working etc. I also found everything SEEMS to be okay with Comcast router downstream...
View ArticleFrozen screen on tablet
The screen is frozen. I touch it but nothing happens. I fixed it one time in setting but cant seem to get there again. Help.
View Article